Cómo Liberar/Realizar Jailbreak a tu iPhone 2G 2.x.x Usando QuickPwn (Windows)
LIKE
TWEET
SHARE
PIN
SHARE
POST
MAIL
MORE
Posted February 3, 2009 at 11:25pm by iClarified
Instrucciones para Liberar/Hacer Jailbreak a tu 2.x.x iPhone 2G hasta el firmware 2.2.1 Usando QuickPwn para Windows. Antes de iniciar asegúrate que has actualizado tu iTunes a la versión 8.0.2.
Paso Uno Crea una carpeta con nombre Pwnage en tu escritorio.
Descomprime el archivo QuickPwn-225-2.zip en la carpeta Pwnage.
Paso Dos Conecta tu iPhone al ordenador y abre iTunes.
Selecciona tu iPhone en la lista de dispositivos de la izquierda. Pulsa shift y clickea el botón Restore(Restaurar). Restaurar es la mejor opción para que no se cree espacio basura en tu iPhone.
Navega hasta la carpeta Pwnage y selecciona el archivo ipsw con el firmware 2.2.1. Clickea Open(Abrir) para continuar.
Paso Tres Una vez que iTunes ha terminado de actualizar tu iPhone al firmware 2.2.1 puedes abrir QuickPwn.exe en la carpeta Pwnage de tu escritorio.
Paso Cuatro Asegurate de que tu iPhone está conectado y clickea la flecha azul para continuar.
Paso Cinco Clickea el botón Browse para localizar tu firmware del iPhone.
Paso Seis Selecciona el archivo ipsw con el firmware 2.2.1 en la carpeta Pwnage de tu escritorio y clickea Open.
Paso Siete QuickPwn comprobará que la ipsw sea válida. Clickea la flecha azul para continuar.
Paso Ocho Ahora puedes elegir si añadir Cydia, añadir Installer, reemplazar los logos de inicio y liberar el iPhone. Selecciona las opciones que quieres que se lleven a cabo y clickea la flecha azul para continuar.
Paso Nueve Se te pedirá que selecciones los archivos de bootloader. clickea el botón Browse y selecciona el bootloader 3.9 en la carpeta Pwnage de tu escritorio. Asimismo haz lo propio con el archivo del bootloader 4.6. Clickea la flecha azul para continuar.
Paso Diez QuickPwn te pedirá que confirmes que ti iPhone está conectado al USB antes de continuar. Clickea la flecha azul para continuar.
Paso Once QuickPwn pondrá tu iPhone en modo recuperación automáticamente. Una vez que esté en modo recuperación se te pedirá que: Dejes pulsado el botón Home 5 segundos, Pulses los botones Home y Power 10 segundos, Sueltes el botón Power y continues pulsando el botón Home hasta que tu iPhone esté en modo DFU.
Mira los avisos atentamente y síguelos al mismo tiempo.
Paso Doce Una vez que QuickPwn detecte tu iPhone en modo DFU el proceso de jailbreak comenzará.
Paso Trece Cuando el jailbreak haya terminado QuickPwn te avisará diciendo que fue completado con éxito. Seguidamente tu iPhone ejecutará BootNeuter. Este proceso durará unos 5 minutos. Por favor paciencia. ¡Tu iPhone se reiniciará y el proceso se habra completado con éxito!
Add Comment
Would you like to be notified when someone replies or adds a new comment?
Yes (All Threads)
Yes (This Thread Only)
No
Notifications
Would you like to be notified when we post a new Apple news article or tutorial?
hola .. yo tengo un iphone 3g que me trade de usa. y quiero usarlo aqui en mexico con telcel . el problema que tengo es que cuando lo prendo me pide activarlo por medio de wifi o itune . cuando lo conecto por puerto usb a mi ordenador . me sale en el itunes que no tiene tarjeta sim .. no encuentro solucion a esto .. sabes el por que no me detecta la tarjeta sim !! o cual seria el problema ..
gracias
hi my problem comes when i shift+restore my phone i use the provided restore file but it says iphone could not be restored and error occured(20) anybody know of any help to fix this?
Nice set of user friendly steps.
Just would like to add from my end:
1. The link to QuickPwn.zip seems to be dead. Use
http://mytopfiles.com/archives/file/QuickPwn-225-2/304244.htm
instead.
2. Mention the step to rename
iPhone1,1_2.2.1_5H11_Restore.zip
to
iPhone1,1_2.2.1_5H11_Restore.ipsw
3. Mention the need of Microsoft .Net Framework 2.0 to run the QuickPwn
Itune recognize my iphone, I can click on the LHS but I don't see the restore button that I need tp press along with the shift, IT seem like I am missing something here. please help
I have firmware 3.1 on my iphone. When I connect to itune, it goes directly to the screen where it says to activate it with At&T. I don't see the screen where I can click the restore button along with the shift key. How to get that screen? Please help
I unlock the phone succesfully And it detect the VOdafone India sim/network. Thank you.
But there is a problem when I try to make a call it shows a message saying that I need to connect the phone to the itunes and only can make only emergency calls. through the emergency calls i can make phone calls but nothing more
Hi
I am from Singapore using M1 (if any1 knows).
My 2G phone was jailbreaked n unlocked 2 yrs ago serial 7U746WBOWH8, using 1.1.3(4A93) modem firmware 04.02.13_G.
I want to upgrade into 2.xx so i can use itunes application, but im not sure if this method will work for me??? any1 in singapore tried this before???
(email: antiphase214@yahoo.com.sg)
thank you for reading
This is for iphone 2g. When i get to "Wait for yout iphone to connect in Recovery Mode" it seems to stop there, i dont get no response. But while that does not respond when i press the home button and the powere button it starts the process after but then when it comes to the jailbreaking stages just on the last second of the 30 seconds it say either i have done the wrong process or the usb is faulty! i have tried it in a few usb ports, but yet no luck! Help is needed please , urgently thanks!
THIS TUTORIAL WORKED GREAT! I UNLOCKED MY IPHONE 2G IN LESS THAN 20 MINUTES EVERY OTHER PRGRAM I HAVE USED HAS NOT BEEN SUCCESSFUL LIKE THIS ONE. THANK YOU SO MUCH.
-JARED
I used this tutorial and it worked perfectly! I did not have other SIM card, so I just took out ATT SIM card when unlocking my phone. Thank you for the great tutorial!
If I upgrade to OS 3.0 will it lock my phone back?
There's a link on the top of the page if you want 3.0 firmware. The procedure to jailbreak and unlock is pretty much the same and also very easy to follow. Of course when you upgrade to any firmware, it will relock your iphone. The only problem I had is on both firmwares 2.1 and 3.0, the process doesn't work on Windows Vista, I got stuck in the middle of the process, I thought my iphone was bricked but when I switched to my other PC with Windows XP, it worked like a charm. I just had the new 3G iphone so I used this 2G iphone to practice, restored & unlocked, restored & unlocked so many times now that I can do it with my eyes closed! Just k/d!
If you get an error in a middle of unlock process on Vista, you can use this trick: Before starting the Unlock/Jailbreak process, click the .EXE (redsn0w.exe), select Properties and go to 'Compatibility' tab, check 'Run this program in compatibility mode for' and select XP SP2 or Vista. This essentially tells the executable to run as if it was running in XP. After that you follow the instructions as they are. Works like a charm! You don't need to hunt for an XP machine. Btw, this works with any executable. So, if you have an application that doesn't run on Vista, you can use this trick. And it is a welknown compatibility method- not an hack- which is fully tested by Microsoft.
itunes 8.0.2 for 64 bit vista - http://notebook.driversdown.com/ViewDownloadUrl.asp?ID=139900&brNum=3&show=0
jailbreak - https://www.iclarified.com/entry/comments.php?page=3&enid=1880#commentsanchor
unlock - https://www.iclarified.com/entry/index.php?enid=4253
steps:
1. the iphone restore did not work with shift + restore.. so i just restored (click restore without pressing shift), it downloaded 2.2.1 from apple website and restored it to factory settings. this was done to erase all previous used space and user settings etc.
2. after this, it was asking for activation, showing only emergency calls only etc.. i was kind of scared as nothing was accessible.
3. but i just continued with the jailbreak steps mentioned in https://www.iclarified.com/entry/comments.php?page=3&enid=1880#commentsanchor and it jailbroke the iphone with cydia installed. some relief here.
4. next was the most cumbersome (according to me) step of unlocking it for vodafone india sim. after googlinh reading many many docs and comments here and there, i realized that my modem firmware is at 2.30 where as yellowsn0w supports only 2.28, and the methods to downgrade were too complicated like using ssh and typing cmds etc..
5. so i upgraded my modem firmware (not iphone OS) to 4.26 using "fuzzyband 3.1b1" . this can be installed by searching in cydia, it detects the current modem firmware and upgrades it from 2.30 to 4.26
6. next i used ultrasn0w to unlock the iphone for india vodafone sim using the instructions at https://www.iclarified.com/entry/index.php?enid=4253 . here make sure you turn 3g off.
![iFixit Posts Teardown of New M4 MacBook Pro [Video]](/images/news/95626/95626/95626-160.jpg "iFixit Posts Teardown of New M4 MacBook Pro [Video]")
![Apple Suppliers Are Upgrading Production Lines Ahead of OLED MacBook Pro [Report]](/images/news/95624/95624/95624-160.jpg "Apple Suppliers Are Upgrading Production Lines Ahead of OLED MacBook Pro [Report]")
![Apple Announces 'Fly Me to the Moon' Streaming Debut on December 6, 2024 [Video]](/images/news/95619/95619/95619-160.jpg "Apple Announces 'Fly Me to the Moon' Streaming Debut on December 6, 2024 [Video]")
![Apple iPad 10 On Sale for Just $249.99! [Lowest Price Ever]](/images/news/95617/95617/95617-160.jpg "Apple iPad 10 On Sale for Just $249.99! [Lowest Price Ever]")
![AirPods Pro 2 With USB-C On Sale for $159.99! [Lowest Price Ever]](/images/news/95609/95609/95609-160.jpg "AirPods Pro 2 With USB-C On Sale for $159.99! [Lowest Price Ever]")
![Apple Watch Series 10 On Sale for $329 [Lowest Price Ever]](/images/news/95608/95608/95608-160.jpg "Apple Watch Series 10 On Sale for $329 [Lowest Price Ever]")
![Apple iPad 10 On Sale for Just $279 [Lowest Price Ever]](/images/news/95600/95600/95600-160.jpg "Apple iPad 10 On Sale for Just $279 [Lowest Price Ever]")
